S-24 Commercial Sectional Doors

Mid-America Commercial Sectional door

Mid-America S-24 Series Commercial Sectional Door

The S-24 Series from Mid-America Door is a value-priced commercial grade door..

The S-24 Series is made with 24 gauge steel on the exterior, and uses 26 gauge steel or vinyl on the interior. Choose optional cost-effective, insulation in between. Windows and Full View on teh S-24.

Standards & Features

  • REVERSE ANGLE: Door overlaps jamb approximately 1" against continuous angle of track support system (angle foot toward door). May be used with wood or steel jambs. The door closes against the base flange of the continuous angle.
  • BRACKET MOUNTED TRACK: Use with wood or steel jambs. Door closes against stop molding.
  • GENERAL: Doors shall be SSI Series as manufactured by Mid-America Door Company.
  • RELATED WORK: Opening preparation, miscellaneous or structural metal work, access panels, finish or field painting, are in the scope of work or other trades.
  • DOOR SECTIONS: Sections will have a nominal 2" thickness, manufactured using exterior roll formed 25 gauge steel and continuous sculpted polystyrene board bonded between the exterior steel face and flush embossed steel interior. Sections will have a tongue and groove meeting rail to provide a weather tight seal between sections. End stiles will be 18 gauge galvanized formed steel. Center stiles will be vertical interior 16 gauge steel plates running the entire section height placed on centers for design requirements. Door sections to have a calculated R factor of 9.4.
  • TRACK: Galvanized steel track systems shall be 2" or 3" depending on door size and will be bracket or angle mounted depending upon application.
  • HARDWARE: Hinges and brackets to be made from galvanized steel. Each roller shall have ten hardened ¼" steel balls. Cables 7x19 strand galvanized aircraft type with a minimum safety factor of 8 to 1.
  • SPRING COUNTERBALANCE: Springs shall be oil tempered, helical wound and stress relieved torsion type. Springs shall be mounted on a continuous cross header steel shaft supported by bearing brackets. Long life springs of 25-50-100 thousand cycles may be specified and are recommended for high usage.
  • FINISH: Paint will be baked on commercial white with a polyester coating.
  • WEATHER-STRIP: Bottom rail of section to include U'd vinyl astragal held in place by aluminum retainer to provide additional reinforcement. Additional weather-stripping available for full width of header and jambs.
  • LOCK: Lock will be interior mount slide lock. (Optional cylinder lock available)
  • VISION SECTIONS: 25 x 5 vinyl frames lites can be provided in either single glaze or double glaze.
  • OPERATION: Operation to be made by manual lift, chain hoist, or electric motor.

Panels & Sections

Panels Wide Sections High
Width Number
of Panels
Height Number
of Sections
Thru 9'2" 1 Thru 8'0" 4
9'3" to 12'2" 2 8'3 to 10' 5
12'3" to 16'2" 3 10'3" to 12' 6
16'3" to 20'2" 4 12'3" to 14' 7
20'3" to 24'2" 5 14'3" to 16' 8

Mounting & Clearance

  Clear
Headroom
Sideroom Depth
Into Room
Centerline
of Springs
  2"
Track
3"
Track
2"
Track
3"
Track
2" & 3"
Track
2"
Track
3"
Track
Standard Lift
Manual 12"
12½" 21" 4½" 5½" Door Height + 18" Door Height + 13½" Door Height + 15½"
Standard Lift
Motor Operated
19" 22½" Door Height + 66"
Standard Lift
Manual 15"
16½" 21" 4½" 5½" Door Height + 18" Door Height + 13½" Door Height + 15½"
Standard Lift
Motor Operated
19" 22½" Door Height + 66"
High Lift
Manual
High Lift + 12" 4½" 5½" Door Height Less Lift + 30" Door Height + Lift + 6½" Door Height + Lift + 7½"
High Lift
Motor Operated
High Lift + 12" 24" One Side Door Height Less Lift + 30"
Vertical Lift
Manual
Door Height + 8" 4½" 5½" 18" Double Door Height + 2"
Vertical Lift
Motor Operated
24" One Side 18"
Low Headroom
Manual
6½" 11" 6" 9" Door Height + 30" Does Not Apply
Low Headroom
Motor Operated
9" 13½" Door Height + 30"

Options

The S-24 Series offers optional insulation. Minimum 1½" thick polystyrene with 26 gauge steel or vinyl backing increases the energy efficiency of your door.


 

Manufacture Term: 

Main Office - ADC North

770-975-3500

  • 4255 McEver Industrial Drive
  • Acworth, GA 30101
  • Fax: 770-974-1455

Fayetteville ADC-South

770-716-3181

  • 500 Marksmen Court
  • Fayetteville, GA 30214
  • Fax: 770-716-3171

Socialize with us

               


The leader in Commercial Overhead Doors!






Google+ Atlanta Door Corp on google+
Go to top